DCS range hood terms CFM, blower, baffle and make-up air show up on every specification sheet, and they are easier to understand once you see the hood as a small system: a canopy that catches the rising smoke, a blower that pulls it in, filters that remove grease, and a duct that carries the rest away. This glossary defines the terms in plain language, using how our pages describe DCS range hoods. For the numbers on your exact hood, use the specification sheet for the model.
What does CFM mean on a range hood?
CFM stands for cubic feet per minute, a measure of how much air the hood can move. A higher number means more airflow, and a pro range with powerful burners, a griddle or a grill module needs more of it. Our range hood CFM sizing guide explains that you should scale the hood’s airflow to the total cooking output, that the hood should be at least as wide as the range, and that rated CFM assumes a short, straight duct: every elbow and foot of run reduces the real airflow. So a rated number is a ceiling, not a guarantee. We do not give figures for particular models here; the specification for your hood has them.
What are the blower and the speeds?
The blower is the fan inside the hood, and our guide on how a DCS range hood works describes a multi-speed blower that creates the airflow pulling the plume into the hood: higher speeds for heavy searing and frying, lower speeds for gentle cooking, and quieter running. If the blower weakens, hums or does not start, see our blower troubleshooting guide and the weak suction page. Do not open the hood housing to look at the blower.
What do canopy and capture mean?
The canopy is the part of the hood that sits above the cooktop and catches the rising plume of smoke, steam and grease. Capture is how well the hood gathers that plume before it escapes into the room. A wider, deeper canopy captures more, which is why sizing matters, and a wall hood captures efficiently because the wall helps direct the air, while an island hood is open on all sides and needs more width and airflow. A hood that is too small or too high does not capture well, whatever its CFM figure says.

What is a baffle filter?
A baffle filter is a stainless filter made of angled plates that force the air to change direction. Grease droplets are flung onto the baffles and drain away while cleaner air passes through, as our range hood guide describes. Clean filters keep this efficient, and clogged filters cut airflow and let grease build up. Our range hood filter cleaning guide explains the routine. A recirculating hood adds a charcoal filter for odor, and that is replaced rather than washed, according to the hood’s instructions.
What is the difference between ducted and recirculating?
A ducted hood carries air outside through rigid ducting, which removes grease, moisture, heat and odor from the home and is the most effective option. A recirculating, or ductless, hood passes air through a charcoal filter to reduce odor and returns it to the room; it handles grease and some odor but returns heat and moisture, so it is a fallback where a duct cannot be run. Know which you have, because it decides which filters you maintain. The installation steps and duct sizes for your hood are in the instructions for your model, and our range hood installation requirements give the general picture.
What is make-up air?
A powerful hood pulls a lot of air out of the house, and the house has to replace it. Make-up air is that replacement, brought in on purpose through a dedicated opening or system. Without it, a tight house can limit the hood’s performance and can pull combustion gases back down a flue, which is called backdrafting. Our make-up air guide explains it, and local code decides when it is required. If your hood seems weak or you notice backdraft, the backdraft page covers the symptom.
Which other terms will you meet?
Lights are usually a separate control on the hood, and our range hood light troubleshooting guide explains what to check. Model numbers of hoods describe size and style, but we do not decode them; use the specification sheet and the rating plate. For service, our DCS range hood repair page explains how a visit works.
When you compare two hoods, read the terms together rather than one at a time. A high CFM paired with a narrow canopy, a long duct and no make-up air will not perform like the number suggests, while a hood sized to the range, ducted in a short straight run with air available to replace what it removes will do its job at a lower setting and a lower noise level. Ask which terms in a specification are measured at the blower and which describe the hood once it is installed, and ask the installer to confirm the duct route before you buy.
How do you read a hood specification sheet?
Look for four things in order: the airflow rating, the width of the hood, whether it is built for ducted or recirculating use, and how the controls work. The airflow rating tells you the ceiling, the width tells you how much of the cooking surface the hood can cover, and the duct type tells you which filters you will maintain. If a figure is not on the sheet, do not guess it from another model; ask the retailer or use the documentation for your exact hood. A spec sheet describes the hood on its own, while your kitchen adds the duct run, the ceiling height and the house itself, which is why an installer should check the plan before you commit.